Guide: Diesel Engine (Spoilers)

ryanb · 2018-12-20 01:00:00

DIESEL ENGINE GUIDE

The Diesel Engine is currently used to craft the Diesel Water Pump and Crude Car. It is expensive to craft, but the resulting objects are pretty powerful.

Prerequisites

Make sure you have the following:

• 17 Steel Ingots (+2 for the water pump)
• 1 Empty Fuel Tank
• 1 Raw Rubber Tire (+4 for car)
• a Multipurpose Newcomen Engine near a Forge
• at least 7 Baskets of Charcoal
• at least 4 Buckets of Water, I recommend a full Cistern nearby.

You will also need the 4 attachments that work with the multipurpose engine:

• Crude Piston on Flat Rock
• Roller Mechanism
• Bore Mechanism
• Lathe Mechanism

The Bore and Lathe can share the same Pully Drive Mechanism by swapping out the heads.

Newcomen Roller

First setup the Newcomen Roller. Like all newcomen engines, it only stays firing for 20 seconds. Since the forge lasts for 30 seconds so it is better to light the forge first. Once they are both firing, pick up a steel ingot in wooden tongs, heat it in the forge, then roll it into steel rods. Do a couple extra if you're making a water pump.

5 Hot Steel Ingots in Tongs
→ 5 Steel Rods (1 hit)

2 Hot Steel Ingots in Tongs (if doing water pump)
→ 2 Steel Rods (1 hit)

Newcomen Hammer

With the Newcomen Hammer and forge, do the following:

12 Hot Steel Ingots in Tongs
→ 10 Steel Piston Blanks (1 hit)
→ 1 Small Pulley (2 hits)
→ 1 Large Pulley (3 hits)

It may take a few tries to get make all of these, but after that you're done with the hammer and forge.

Newcomen Bore

Using the Newcomen Bore, apply the following:

2 Steel Piston Blanks
→ 2 Steel Cylinder Blanks (1 hit)

3 Steel Rods
→ 3 Steel Pipes (1 hit)

2 Steel Rods (if doing water pump)
→ 1 Steel Pipe (1 hit)
→ 1 Pump Valve Jacket (2 hits)

Newcomen Lathe

Fire up the Newcomen Lathe and apply the following:

2 Steel Rods
→ 1 Cam Shaft (1 hit)
→ 1 Crank Shaft (2 hits)

2 Steel Cylinder Blanks
→ 2 Precision Cylinders (1 hit)

2 Steel Pipes
→ 2 Fuel Nozzle Body (1 hit)

8 Steel Piston Blanks
→ 2 Precision Pistons (1 hit)
→ 6 Steel Valves (2 hits)

That's it for the difficult timing part. Now you can craft everything together.

Cam Timing Assembly

1. Put the Large Pulley on a Long Straight Shaft, and then add the Small Pulley.
2. Apply the Raw Rubber Tire to get the Raw Rubber Belt and then cook that in a Hot Adobe Oven
3. Cut the belt with a Knife and add to the construction.
4. Add a Cam Shaft to complete your Cam Timing Assembly

Diesel Piston Head

Make 2 of these:

1. Add two Steel Valves to a Precision Cylinder
2. Add Steel Valve to Fuel Nozzle Body and then add to the previous cylinder
3. Add Precision Piston to make the Diesel Piston Head

Diesel Engine

1. Combine the two Diesel Piston Heads
2. Add the Crank Shaft and then the Cam Timing Assembly
3. Add a Steel Pipe to a Fuel Tank and combine with the previous construction

Pat yourself on the back, you just finished the Diesel Engine! Now what do you want to do with it?

Diesel Water Pump

1. Combine the Steel Pipe with Pump Valve Jacket
2. Add that to a Dry Shallow Well
3. Add the Diesel Engine
4. Add Kerosone to start

The pump will give you 7 buckets of water and only uses 1 Kerosene to refill.

Crude Car

1. Cook 4 Raw Rubber Tires in a Hot Adobe Oven
2. Combine with 4 Wooden Wheels (Butt Log + Bow Saw + Flint-tipped Bow Drill)
3. Combine wheels into sets of 2 and then all together
4. Make a Wooden Box (Butt Log + Froe + Mallet + Rope)
5. Add wheels and Diesel Engine to box
6. Add Kerosone to start

The car will run for two minutes and you will be invincible while driving. Minimum driving age is 16. You travel 3 times the walking speed while driving, it's fast!

Last edited by ryanb (2018-12-21 21:37:14)

Joseph Stalin · 2018-12-20 01:15:29

oof thats complicated

Azrael · 2018-12-20 02:09:17

Awesome guide!

Only thing I would add is to put the requirements for the car in the prerequisites, like the box and wheels.

Other than that, this is very informative! Job well done.

ryanb · 2018-12-20 16:14:51

Azrael wrote:

Only thing I would add is to put the requirements for the car in the prerequisites, like the box and wheels.

I wanted to keep the focus on the diesel engine, so I just mention the car and water pump ingredients that are already part of the engine so they can make it in bulk.

Azrael · 2018-12-20 21:21:55

I see... well awesome post anyways, you should do one for guns (when they come out) I'm hoping within a few months

pein · 2018-12-21 09:02:36

yeah i kinda realized that the lathe and the bore interchangeable, and most importantly saves a belt for timing belt

people collecting lot of iron but they are weak on the rope/bucket/tire/raw tire part so i cant do it in one life

btw if you don't have bore you don't have pumpjack, and you need the extra blade and pipe for that too, so yeah, once someone made one, might be easier but 0 to 100 is a lot of details

Baker · 2018-12-21 10:19:49

Thanks for the guide, It's nice knowing exactly what you need. Helps me be more efficient with the machines. I wouldn't be opposed to getting kerosene or even diesel engine powered rollers, bores, hammers, and lathes.

To think that smithing used to be considered advanced.

InSpace · 2018-12-21 20:37:16

Better than peins guide

One Hour One Life Forums

#1 2018-12-20 01:00:00